lowering the rear of a bike, for free with no welding.

[snydur]

last of of today.
on your way home, find a rusty, completely shot brake pad

clean it up

bolt it on

and in five minuites, your bike sits afew inches lower, and is a tad bit longer.

you will have to drill a hole in the"bracket" to bolt it in a second place, just so it stays
oooooor, add a spring from the bottom of the bracket to somewhere on the frame, and you can now have a full suspension bike.

[EasyRider420]

thats a wicked cool idea man i got a bike that needs somethin extra i think this is it!!!! thanks again for sharing your creative juices!!
-Easy Rider

[snydur]

ive just wondered why the fronts of bikes are always lowered ,but not the back. found a solution.

[miloziffel]

Have you checked chain clearance? Great idea!

[snydur]

chain clearence was my first thought honestly. but it seems to not be all that bad.


it does rub a little, but i believe thats just because there is onyl one side. once i find anouther pad, and add some washers (to mahe up for the width of the frame) it should be fine.

[harquahalas]

This looks like a really cool idea. I wonder if it will stay in position well for riding?

[snydur]

This looks like a really cool idea. I wonder if it will stay in position well for riding?

fixed that to! i drilled a hole through the brake pad that lines up with the stock hole for the rear fender. put a grade 8 bolt through, and wallah! no longer has a pivot point.

[harquahalas]

This looks like a really cool idea. I wonder if it will stay in position well for riding?

fixed that to! i drilled a hole through the brake pad that lines up with the stock hole for the rear fender. put a grade 8 bolt through, and wallah! no longer has a pivot point.

Perfect! All bases covered

[snydur]

This looks like a really cool idea. I wonder if it will stay in position well for riding?

fixed that to! i drilled a hole through the brake pad that lines up with the stock hole for the rear fender. put a grade 8 bolt through, and wallah! no longer has a pivot point.

Perfect! All bases covered

now all i got to do is find a pair of brake pads so i can do both sides, and ride this.

[Spokeshave]

I'm going to dig for a pair of junk pads -This looks like a perfect fit for my current project.

[snydur]

i went to the store today and bought afe washers. added two washers on each side of the axle to bing the wheel over, and everything lines up prefectly. maybe even better than before. i think i have 5 bucks in this so far (bought new nuts, bolts, washers, etc)

[outskirtscustoms]

Awesome, i got some thick metal plates from a shifter I got at a yard sale. This gives me ideas now.

[snydur]

well this is about it, untill i can find a pair of old brake pads (harder than i thought it would be). tubes are on and it, and the bike still sits knee high at the handle bars (im 6'1") washers are on and it lines up perfectly. i put a spacer to mock up where the wheel would be when the other side is done, and everything went perfect.


previously mentioned spacer/tail light off a trailor

shorter grade 8 bolts so i dont jab my leg into the sides. and i got to admit it looks pretty dang good.

if anyone has found a pair and bolted them on, please feel free to post pictures for the rest of us. thanks

[someguy83]

Are you using the same length of chain as previous or did you have to add a few links? You gave me a great idea thanks

[snydur]

Are you using the same length of chain as previous or did you have to add a few links? You gave me a great idea thanks

ooooh! dur. yes i did add some links. 12 to be exact (may be less if anyone else does it, cause i also took the chain off a bike with smaller sprocket)