Mystery Frame, what cranks would work?

Rat Rod Bikes Bicycle Forum

Help Support Rat Rod Bikes Bicycle Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Joined
Dec 27, 2008
Messages
178
Reaction score
175
Location
Cato, NY
Rating - 100%
14   0   0
I recently picked up this interesting frame. Sorry for the poor pictures. It was reported to be a 1920-30's Mead Ranger-but certainly isn't. Check out the chain tensioners on the rear dropouts. The serial number is on the seat stay as opposed to being entered with dies on the bottom of the bottom bracket. Slight damage to the top frame bar and a small cut on the rear frame bind the bottom bracket It's still a neat frame, powder coated. The bottom bracket is 2 3/4" wide and has a 1.5" (approx.) diameter, so the traditional conversion sets won't fit, no threads on the inside. Are there any 3 piece units that would fit it? Other wise it would require a bottom bracket transplant, which I've done successfully before. What would you do? What could I do?
 

Attachments

  • IMG_20240222_124743.jpg
    IMG_20240222_124743.jpg
    169.4 KB
  • IMG_20240222_125142.jpg
    IMG_20240222_125142.jpg
    165.1 KB
  • IMG_20240222_125352.jpg
    IMG_20240222_125352.jpg
    139.7 KB
  • IMG_20240222_124716.jpg
    IMG_20240222_124716.jpg
    156.3 KB
Last edited:
I've seen them, will they fit the smaller diameter bottom bracket ( 1 3/4 as opposed to the "normal" 2") that this frame has?
 
I have a frame that uses an odd size BB. The shops had the crankset but they were all old stock. I'll measure it and see the exact diameter.
red tiger.jpg
 
Last edited:
I recently picked up this interesting frame. Sorry for the poor pictures. It was reported to be a 1920-30's Mead Ranger-but certainly isn't. Check out the chain tensioners on the rear dropouts. The serial number is on the seat stay as opposed to being entered with dies on the bottom of the bottom bracket. Slight damage to the top frame bar and a small cut on the rear frame bind the bottom bracket It's still a neat frame, powder coated. The bottom bracket is 2 3/4" wide and has a 1.5" (approx.) diameter, so the traditional conversion sets won't fit, no threads on the inside. Are there any 3 piece units that would fit it? Other wise it would require a bottom bracket transplant, which I've done successfully before. What would you do? What could I do?

With those dropouts I'd offer that it might be an Iver Johnson. I found the 1941 Iver Johnson
Super MoBike fits the description pictured above. Note dropouts, seat clamp bolt location,
bottom bar positioning, and curve of the frame and the straight bar. Match?

photo: TheCABE, LookN4bikes
1708652490637.png
 
Last edited:
With those dropouts I'd offer that it might be an Iver Johnson. I found the 1941 Iver Johnson
Super MoBike fits the description pictured above. Note dropouts, seat clamp bolt location,
bottom bar positioning, and curve of the frame and the straight bar. Match?

photo: TheCABE, LookN4bikes
View attachment 259336
I think you are correct! I love the wealth of knowledge and the the willingness to help on the forum!
 
I think you are correct! I love the wealth of knowledge and the the willingness to help on the forum!
In my case it's a little bit of knowledge, a little bit of OCD and the winter blahs. Shake in a dash
of luck... Wah lah! Originally I thought it might have been a Gormley & Jeffery, but too early on
those TOC frames. I like the Heineken green on that one. Nice.
 

Latest posts

Back
Top