Girthy Gerty

Rat Rod Bikes Bicycle Forum

Help Support Rat Rod Bikes Bicycle Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I have made a bunch of fender brackets from 1/8" thick x 1/2" wide steel stock. Bends in a vise,holds it's shape, supports weight, drills and cuts relatively easily, and takes on a faux-tina like nobody's business.

Diggin' the stance!
Appreciate the advice. Will definitely try that
 
I have made a bunch of fender brackets from 1/8" thick x 1/2" wide steel stock. Bends in a vise,holds it's shape, supports weight, drills and cuts relatively easily, and takes on a faux-tina like nobody's business.

Diggin' the stance!
I'll bet those could be used as supports like truss rods or struts on springers.
 
I'm a sucker for dimples. So tonight I decided it's time to use the tools I've had for ages to try and get me some. Dimples, that is... Used my dimple die set for the first time
IMG_20220516_200134757_HDR.jpg
It marks the line
IMG_20220516_200146588_HDR.jpg
It drills the holes
IMG_20220516_201251964.jpg
And then it gets full of... Dimples
IMG_20220516_202455900.jpg
IMG_20220516_202503033.jpg
I wanted to use the 3/4" dimple die, but it won't fit in my press with the guard. Maybe next time
 
Like a bolt out of the blue, I had an idea for the license plate rack. I've had a lady Huffy Camaro tank for a while now and couldn't figure it how to convert it into a men's tank. I was watching Vice Grip Garage's budget rat rod build video and realized I had a whole stack of steel license plates just rusting away in the corner of the shop. So I tottled out there, picked the crustiest plate of the lot, and decided to show off my state's plate by hacking it onto the tank, which is now spread eagled.
The victim, pre surgery
IMG_20220517_191347321_HDR.jpg

Sizing it up. I wanted it to support as much of the plate as possible. I'm going to weld tabs onto the tank so the plate can bolt on using the existing mounting holes
IMG_20220517_191432383.jpg

This is the profile I was going for
IMG_20220517_191742056_HDR.jpg

A Tack attack!
IMG_20220517_201641914.jpg
IMG_20220517_201614212.jpg

Then I hollowed it out like a pumpkin
IMG_20220517_203543035_HDR.jpg
IMG_20220517_203535109.jpg

I got pretty close to the intended profile. Any lower and the tank will go over the edge of the fender, ruining the profile of the fender
IMG_20220517_203526143_HDR.jpg
IMG_20220517_203509878.jpg

I'm going to see if I can't find some small taillight lenses like a 59 Cadillac DeVille and stuff them in the (now) taillight housing. I finally, actually, mounted the tank, and as an added bonus, installed the National Hyper Siren
IMG_20220517_204711288_HDR.jpg



IMG_20220517_204716058.jpg
IMG_20220517_204726293.jpg
 

Attachments

  • IMG_20220517_203535109.jpg
    IMG_20220517_203535109.jpg
    586.5 KB · Views: 20
  • IMG_20220517_201641914.jpg
    IMG_20220517_201641914.jpg
    299.1 KB · Views: 12
  • IMG_20220517_201634881_HDR.jpg
    IMG_20220517_201634881_HDR.jpg
    236.2 KB · Views: 16
  • IMG_20220517_201614212.jpg
    IMG_20220517_201614212.jpg
    310.5 KB · Views: 12
  • IMG_20220517_191432383.jpg
    IMG_20220517_191432383.jpg
    429.5 KB · Views: 16
  • IMG_20220517_191347321_HDR.jpg
    IMG_20220517_191347321_HDR.jpg
    498.1 KB · Views: 21
  • IMG_20220517_203543035_HDR.jpg
    IMG_20220517_203543035_HDR.jpg
    419.4 KB · Views: 21
  • IMG_20220517_203519740.jpg
    IMG_20220517_203519740.jpg
    523.6 KB · Views: 16
  • IMG_20220517_203509878.jpg
    IMG_20220517_203509878.jpg
    871.8 KB · Views: 13
  • IMG_20220517_201634881_HDR.jpg
    IMG_20220517_201634881_HDR.jpg
    236.2 KB · Views: 23
Last edited:
I changed a bunch of things today, like the fork, rear wheel, and driveline, so I could take the bike out for the first ride with the new extension. For using the absolute worst materials that seemed even remotely in the realm of probably working, it held up surprisingly well. I built this extension from 14 ga. hot rolled, galvanized sheet steel. The extension piece is still completely flat with very little structural integrity, and it was able to support my 210 lb body for almost half an hour, when I rode off a curb and folded the rear end. The Mk.II version will correct several fitment and structural integrity issues I've noticed, and also the design will change slightly, as the bike needs about 1/2" more ground clearance.
 

Attachments

  • first ride.mp4
    3.2 MB
Well, I managed to fix what I broke last week. On version 1.3 (revised), I welded a piece of round stock onto the inside of the seat stay part of the extension for additional strength. For the minimal amount of effort used on the repair, it has held up with flying colors
IMG_20220529_153119551.jpg

I was able to ride for hours around Grand Haven without issue. Which proves that with just a little reinforcement, my flat steel piece will hold up.
IMG_20220529_143841842_HDR.jpg
IMG_20220529_144804793_HDR.jpg
IMG_20220529_133805131_HDR.jpg
IMG_20220529_131602864_HDR.jpg
 
I'm trying to design a total bolt on system, no welding required. This is my first attempt with plate steel that I knew was too thin for the job, but the only thing I had on hand at the time. Either 1/8" or 10 ga. cold rolled steel would be perfect and a lot stronger than the hot rolled, galvanized 14 ga. I used here
Looking good. I'm going to have to get a welder some day so I can try a bolt-on extension like that.
 
Looking good. I'm going to have to get a welder some day so I can try a bolt-on extension like that.
If you check out my other builds Full Monty and
El DoRato, you'll see that I usually hack the rear triangle off a tall road bike, flatten the seat stay tubing, then bolt it onto my chosen victim's frame. The mod on Full Monty allowed the use of 29" wheels on a 26" frame without cutting or welding the frame
 
Last edited:
Went on a group ride around downtown Grand Rapids tonight and couldn't resist taking some photos.
IMG_20220603_183719850_HDR.jpg
IMG_20220603_181633030_HDR.jpg

My bike became a kickstand for a Penny Farthing while parked next to the Paddy Wagon halfway through the ride
IMG_20220603_183945195_HDR.jpg
IMG_20220603_183938945_HDR.jpg
 
Well, the time has come. I'm finally going to wash the frame and try to clean up some of the crud on it to find the serial number. I haven't done anything cleaning or maintenance wise to it since I bought the bike last year, and in handling it this last month some bright green paint has revealed itself from under the rust and gunk. This genuinely surprised me today, as I thought there was zero paint left on the frame. I thought the bike might have originally been black, but couldn't tell for sure from the amount of patina it has acquired
FB_IMG_1653867586991.jpg
 
Me, at a yard sale today.
Polish_20220609_205951840.jpg

But it was only $5, so what harm could come from it?
IMG_20220609_203844143.jpg
IMG_20220609_203854111.jpg
IMG_20220609_203904609.jpg
Sizing matters up... Well I'll be a witches Uncle, these fenders will fit over an 80mm rim with a 2.5" tire, and with room to spare!
IMG_20220609_205256194.jpg
IMG_20220609_205504706.jpg

And for the icing on the cake, the original paint under the terrible black rattle can paint matches the blue on the tank! No freaking way! Well, I guess I ought to, I'm staring right at it with my peepers.
 

Latest posts

Back
Top