Tips n Trix
- Thread starter MattiThundrrr
- Start date
Help Support Rat Rod Bikes Bicycle Forum:
- Joined
- Sep 17, 2013
- Messages
- 4,295
- Reaction score
- 9,472
This is a good idea. I ran into this in 1962 when a close mechanical genius friend rebuilt a ford 390 police interceptor engine. He wasn’t old enough to drive yet. His dad had a 1957 Fairlane and the engine died. He convinced his dad that he could put an engine in it. He used egg cartons to keep the lifters arranged and a tree branch in the yard as an engine stand and hoist. Here ya go dad, all fixed. His dad pulled out of the driveway, gave it the usual amount of gas and burned a patch in the street. He had ulterior motives as it ended out being his car for high school. After HS he got a blown up 427 and put the cam, heads, intake and cast iron headers on the 390. In his 40s he built a cobra replica with a classic 427 in it. He bought one piece at a time but to save money he built his own frame. The fiberglass body, used for frame measurements, sat on a trailer for 4 years while he collected parts. The original mag wheels were $1200 each and the gas cap was $200. Back then you could buy a car for all that.
- Joined
- Sep 17, 2013
- Messages
- 4,295
- Reaction score
- 9,472
The drops were hardened so it took quite awhile.
Want to label your screw boxes?
Here's the perfect font for you!
Grab it for free under the SIL open font license at: http://www.peter-wiegel.de/Schraubenkiste.html
Found it through this link:
https://mastodon.art/@luckyresistor/112424613434646199
Here's the perfect font for you!
Grab it for free under the SIL open font license at: http://www.peter-wiegel.de/Schraubenkiste.html
Found it through this link:
https://mastodon.art/@luckyresistor/112424613434646199
MattiThundrrr
Rattus All Terrainus
MattiThundrrr
Rattus All Terrainus
@CRASH came up with an upgraded version of the stay crimping tool
https://ratrodbikes.com/threads/how-to-beefier-frame-crimping-tool.119807/
stays.
https://ratrodbikes.com/threads/how-to-beefier-frame-crimping-tool.119807/
stays.
The Renaissance Man
__CERTIFIED DIVER__ (Open Water & Open Dumpster)
Staff member
Moderator
Pro Member
These truss rods were very wobbly. Let's get them straight!
Because they are hollow tubes, I had to be very careful with straightening them. Clamping them in the vice was out of the question. I decided to make a wooden buck to sandwich over the tube to avoid crushing it in the vice.
A second buck was used outside of the vice. The gap between the two bucks served as an alignment gauge. By rotating the tube inside the bucks, the gap would open or close revealing the direction of the bends. It worked very similarly to truing a wheel.
Once the bend was located, the outside buck was gently used to push and pull the bends back to straight.
This was a rinse-and-repeat process up and down the tube until all the bends were gone.
Several hours later...
Because they are hollow tubes, I had to be very careful with straightening them. Clamping them in the vice was out of the question. I decided to make a wooden buck to sandwich over the tube to avoid crushing it in the vice.
A second buck was used outside of the vice. The gap between the two bucks served as an alignment gauge. By rotating the tube inside the bucks, the gap would open or close revealing the direction of the bends. It worked very similarly to truing a wheel.
Once the bend was located, the outside buck was gently used to push and pull the bends back to straight.
This was a rinse-and-repeat process up and down the tube until all the bends were gone.
Several hours later...
- Joined
- Sep 17, 2013
- Messages
- 4,295
- Reaction score
- 9,472
Install grease zerks in pedals.
All steel vintage pedals. I installed grease zerks in the dust caps of vintage all steel pedals and then cleaned the races and bearings. Then greased them and then assembled. Zerks are from Tractor Supply.
All steel vintage pedals. I installed grease zerks in the dust caps of vintage all steel pedals and then cleaned the races and bearings. Then greased them and then assembled. Zerks are from Tractor Supply.
frayed cable ends hack. This is neat.
Bearing holder for scrubbing old filthy bearings...
Lone Star Beer cap, old toothbrush & a stack of powerful magnets...
worked like a charm
Lone Star Beer cap, old toothbrush & a stack of powerful magnets...
worked like a charm
MattiThundrrr
Rattus All Terrainus
MattiThundrrr
Rattus All Terrainus
Wildcat shares his opinion on Sturmey Archer 3 speed hubs:
" I never take them apart to lube, they usually have an oil port on the hub shell. Light oil like good machine oil is what works best. I also remove the shift chain and add light oil right down in the axle where the chain attaches to get the oil all in the guts. Once it gets all worked in that's when the gears can be adjusted perfectly. The shift chain could probably use some oil also"
along with some great advice for a quick cleanup:
" I never take them apart to lube, they usually have an oil port on the hub shell. Light oil like good machine oil is what works best. I also remove the shift chain and add light oil right down in the axle where the chain attaches to get the oil all in the guts. Once it gets all worked in that's when the gears can be adjusted perfectly. The shift chain could probably use some oil also"
Neither of mine have oil ports. You can still oil and clean them thru the chain hole.
Spray thru the hole with an aerosol can penetrating oil, tip the hole down, and shoot 60 psi air up through the hole while working the hub. That brings the oil back out.
Repeat until any grit is flushed, then put in some nice light lube oil. Work it in, spray it out & relube.
This revived the SA canal victim I rescued.
That bike had mud in every pore.
Spray thru the hole with an aerosol can penetrating oil, tip the hole down, and shoot 60 psi air up through the hole while working the hub. That brings the oil back out.
Repeat until any grit is flushed, then put in some nice light lube oil. Work it in, spray it out & relube.
This revived the SA canal victim I rescued.
That bike had mud in every pore.
Most of you with modern mtbs have probably seen this fancy tool:
One of the MC shops I worked at had a salty old service manager that liked to make specialty tools. He always labled them Mac-On or Smash-On tools.
One of the MC shops I worked at had a salty old service manager that liked to make specialty tools. He always labled them Mac-On or Smash-On tools.
Last edited:
I just discovered, that my go to source for all things F+S coaster brake hubs had an English version of it's site.
Here you go for loads of info in form of scanned documents and helpful videos:
http://www.torpedo-coasterbrake.com
Here you go for loads of info in form of scanned documents and helpful videos:
http://www.torpedo-coasterbrake.com
My favorite tire spoons are a metal set I got in the 80's (has it really been about 40 years?) To make the spoons slide easier between the rim and tire I bevel the edges of the spoon a little more using a file. Then I polish it a little with sandpaper. Might be over kill but sometimes it's the little things.
Someone stole one of my .... Cepek bead breaker irons. I only have half a set.
I should look on ebay….
I have a nice set of big craftsman spoons from the ‘60s and the chrome is still nice.
For motorcycles, I also have a small set from Motion Pro, plus the nylon rim cushions.
Then, a tiny Quick Stick for bicycles.
I should look on ebay….
I have a nice set of big craftsman spoons from the ‘60s and the chrome is still nice.
For motorcycles, I also have a small set from Motion Pro, plus the nylon rim cushions.
Then, a tiny Quick Stick for bicycles.
Well I guess I’m lucky that my name isn’t ..... But I guess D.i.c.k Cepek won’t be advertising here.
MattiThundrrr
Rattus All Terrainus
Wildcat dropping knowledge on how to spread the rear stays:
"I would line up the 2 x 4 between the seat stays and chain stays at the same time and widen them both together that way. I would widen them well past the width I needed then remove the 2 x 4 to see how much width it still had. Once it's wide enough, then the dropouts need to be lined up as they will point outwards.
I also used a wide mallet and hammered it up into the stays and did the same thing, then clamped the dropouts to get them straight."
"I would line up the 2 x 4 between the seat stays and chain stays at the same time and widen them both together that way. I would widen them well past the width I needed then remove the 2 x 4 to see how much width it still had. Once it's wide enough, then the dropouts need to be lined up as they will point outwards.
I also used a wide mallet and hammered it up into the stays and did the same thing, then clamped the dropouts to get them straight."
Last edited:
