Freeliner with 3 x 1 gearing is GO!

Rat Rod Bikes Bicycle Forum

Help Support Rat Rod Bikes Bicycle Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I decided to smooth out the welds at the ends of the top tubes with spray filler/primer. A little more tomorrow and its done. I didn’t apply filler to the welds at the bottom bracket.
E10BF6AC-FE9A-4C2A-A24F-4CDE814CA1F6.jpeg
75EE7EA6-0299-4FA6-BA57-F91CA0F9F6E6.jpeg

747F6FFB-B278-40DC-8945-A8A2166C03F9.jpeg
 
Thanks. It took a heap of work to get all the welds at the top section of the frame smoothed out. The factory used lead filler in those areas in the 1930’s and most of it was blasted out when the frame was stripped.

The downtube also had a slight bend and a heap of dents which i repaired with filler. It came out surprisingly good and looks much straighter than before.

The forklift is an electric Toyota we use at work. Its very simple to use and has a top speed of 8mph. 🤣It has done over 20,000 miles.
C1E6C5B3-9957-486F-8126-15CCE06BF46C.jpeg
 
Last edited:
Thanks. It took a heap of work to get all the welds at the top section of the frame smoothed out. The factory used lead filler in those areas in the 1930’s and most of it was blasted out when the frame was stripped.

The downtube also had a slight bend and a heap of dents which i repaired with filler. It came out surprisingly good and looks much straighter than before.

The forklift is an electric Toyota we use at work. Its very simple to use and has a top speed of 8mph. 🤣It has done over 20,000 miles.View attachment 216768
Sweet…. We have a propane Toyota at our shop. (Electronics manufacturing)
 
We had a very wet spring and start to summer down south in Australia. However the weather has improved the last few days so today I began spraying the color on the frame.

I sprayed the white for the accents on the front part of the frame. I will wait a week before applying the stencil kit and spraying the final color.
39B6F792-44E6-4B34-85D1-D1A5ED2AA442.jpeg
 
The paint is finally done. Mother nature provided me with a perfect day for spraying, so I grabbed the 2 cans of VHT Mopar engine orange I ordered months ago and left them in the sun for a while. I sprayed out the color and then around 20 minutes later I got started on the arduous task of peeling the tape. I used an arts and craft knife to lift the masking tape off at the thin ends and it worked well.

I’m really happy with the final result and will leave the paint to cure for a week before reassembling the bike.

Have a great New Year everyone.
A588BE15-BE15-4DCD-952B-33E1CDEE76FB.jpeg


E767C295-810A-4D55-A902-1DF5964B713D.jpeg
7CB3C360-0851-4DE3-A590-012273640875.jpeg
 
We have had a few very hot days downunder this week which has helped the paint to cure so this morning I started to reassemble the bike.

First task was to go over the bright yellow Maxxis branding on the DTH tires that I got in a recent swap with some tire black. It dried quickly and seems durable.

Next I fitted the fork using a new Tange MX-2 headset but swapped the 26.4mm crown race for a 27mm one. The YST bottom bracket conversion kit for the 3 piece crank set took some time to set up and spins nicely. I will use Loctite on the bolts once I get the bike on the ground. Lastly I serviced the front hub and cleaned off the brake pad residue frm the Araya rims.

I still have a heap of stuff to do but hope to get the bike done by the end of the week so I can take it on some trails and shoot some photos.
E576CBF0-E4D1-47CE-B476-13FED64B25B2.jpeg
B0C89AAD-65B3-4D38-B929-15D0EF4B0699.jpeg
440C4EE9-1BE1-40E7-9798-0FED5026C9B7.jpeg
 
Last edited:
First ride of the year and shakedown ride for the Freeliner. I bombed all over town and it rode flawlessly with the only issue being a little play in the bottom bracket.

It tracks well and I found the gears to be much closer than those in a Nexus 3 or new Sturmey Archer 3 speed. In top gear (48/18) it is quite fast and feels
more direct than an IGH. The combination of the Changstar front canti brake setup and SA rear drum pulled the bike up easily on a few steep downhill runs.

I really am surprised with the transformation. I remember doing a quick build of this frame in 2020 with a traditional longhorn bar and its original short stem and it was terrible. The stiff front fork, long mtb stem, Electra bar and long seat post have transformed it into a great bike to ride even for someone as tall as me.

The weather is heating up tomorrow but I hope to get another ride in over the weekend on a local trail. I also need to catch up on everyone’s builds.
5E37C3E4-E0A5-4444-806B-29AE1E41C2BE.jpeg

97B5FB29-2282-4C0C-A555-FF9E46DFAF21.jpeg

C3512E3F-E353-4DC5-8E80-DE8EFBFBC4A7.jpeg

9002AE03-18C8-4809-BE85-C4D7789CDB35.jpeg
 
Last edited:

Latest posts

Back
Top