Phoenix Pro street Done ! moving it over to the finished thread ! Video Added

[c1run1]

I'm with @OddJob on this, it looks good right where it's at. Too low sometimes looks a bit forced. Is the very bottom tube parallel with the ground? That's the line eyes will see. awesome whatever you do. This one will definitely win some votes.

Guitarl.

No its not really Parallel to the ground so if i drop the front end even a half inch it would be an improvement .

 

[c1run1]

Alrighty some parts showed up today how ever 28* degree weather not much is getting done .

The kick stand and Handle bars


Sent from my iPhone using Tapatalk

 

[c1run1]

Ok so tonight I took that half inch out of the front end and it looks great ! But while it was apart I added some welds and grounded a bit smoother . The reason for this is the last time I sent a set of these out to chrome the platter had a hard time getting chrome to stick in this sharp grove he said it's not conducive with the fine gap there . After three tries it worked but I hope this fixes that issue .

I also fit the kickstand and tacked it in place

Sent from my iPhone using Tapatalk

 

[LukeTheJoker]

Nice work!

 

[c1run1]

So I ground down the weld and re welded it solid and cleaned it up

I also got a little something in the mail today so I had to check it out on bike . A sick shifter from Boxkars!

A little something old and something new

Sent from my iPhone using Tapatalk

 

[OddJob]

Shifter works well with the design! Can't remember, is that steel tubing or aluminum on the frame?

 

[c1run1]

steel is real

Shifter works well with the design! Can't remember, is that steel tubing or aluminum on the frame?

 

[c1run1]

Not much to report I broke the bike down today and did some last minute details like drill one more cable hole and welded a nut in the frame for a cable stop it's off to powder coat and plate tomorrow.

Sent from my iPhone using Tapatalk

 

[Chad T]

Dang...this one is killer! Love those wide polished hoops!

 

[c1run1]

I had a run in with Godzilla he said build a bitchin bike or else !
Ok so I'm in limbo waiting for my parts to come back from plating [emoji53]it's going to be a long week or two

Sent from my iPhone using Tapatalk

 

[c1run1]

My powder coater sent me a sneak peak at the frame in the blue i picked out it's a three stage color with a base ,color,clear .

Sent from my iPhone using Tapatalk

 

[LukeTheJoker]

Powder looks good!

 

[c1run1]

Some parts showed up today i powder coated a chain wheel the same color as the bike but then I ran across this anodized one I think I like it much better . I also found some anodized blue chain and cable caps all imported from China lol

 

[c1run1]

It's not always cup cakes and candy when re building problems arise , the powder coater applied to many coats of clear so some sanding and prep work is needed so parts fit once again


Sent from my iPhone using Tapatalk

 

[c1run1]

Ok today I cut and polished the frame a bit more to give it a smoother look

FYI polishing powder coating is a bit more work then paint [emoji123]


Sent from my iPhone using Tapatalk

 

[c1run1]

Chrome was picked up Friday now I have to get busy and not for nothing a bad time to get sick with the flue

Sent from my iPhone using Tapatalk

 

[Captain Awesome]

Powdercoat looks sick!

 

[Jaypem]

Very nice!
Super Bad look... Really like the square tube look

 

[TV Casualty]

Great project!

 

[c1run1]

Well I thought I had a 26x4.9 tube and I don't the one that's in there now has tube fold from stretching in the back and I wanted to change it out . I had to order one asap I don't know if it will be in on time [emoji17]


Sent from my iPhone using Tapatalk