I'm not familiar with the reference, this is the closest I could find
It's been some twists and turns, who knows where it's going to wind up now.
SWB0 Grand Jubile aka the Newbury Watusi
- Thread starter Pondo
- Start date
Help Support Rat Rod Bikes Bicycle Forum:
I'm not familiar with the reference, this is the closest I could find
It's been some twists and turns, who knows where it's going to wind up now.
I'm not familiar with the reference, this is the closest I could find
It's been some twists and turns, who knows where it's going to wind up now.
Waterloo is the headquarters for Trek
Watusi because you’ve definitely been dancing your way through this up until now
Yes, that's the perfect moniker for this crazy build!
I noticed this old frame that I had forgotten about up in the garage rafters. Third time’s a charm I guess. It’s an 80s Diamond Back that I pulled out of the trash many years ago. The parts got used for another project back then.
It’s an 18” frame which is the size I would prefer for this build. The Motobecane is 22 1/2” and the Trek 16”. Moto-be-gone:
I had painted this frame before but didn’t wind up building it. The paint is okay-ish so I’m going to leave it. Also the head tube is long enough that I don’t have to cut down the fork steer tube. The Shimano 600 headset went in a little tight but then the forks bolted right up. Next to see if the cranks are going to work.
It’s an 18” frame which is the size I would prefer for this build. The Motobecane is 22 1/2” and the Trek 16”. Moto-be-gone:
I had painted this frame before but didn’t wind up building it. The paint is okay-ish so I’m going to leave it. Also the head tube is long enough that I don’t have to cut down the fork steer tube. The Shimano 600 headset went in a little tight but then the forks bolted right up. Next to see if the cranks are going to work.
Last edited:
I didn’t want to forget about the bell so I cleaned it up a bit. It’s pretty crusty but I think it will fit the build. It’s a neat old rotating bell. I couldn’t find out much about it online.
I’ve decided to run the drivetrain as a 1x for now so the 52t chainring had to go. I got after the old worn out 40t inner ring with my dental grade ultrasonic cleaner as it was fairly caked with old lube and dirt. It will serve as a bash guard of sorts.
The 38t clears the chainstay by just enough.
Looks half decent like this too
Onward…
I’ve decided to run the drivetrain as a 1x for now so the 52t chainring had to go. I got after the old worn out 40t inner ring with my dental grade ultrasonic cleaner as it was fairly caked with old lube and dirt. It will serve as a bash guard of sorts.
The 38t clears the chainstay by just enough.
Looks half decent like this too
Onward…
Drivetrain looking 
Drivetrain looking
Thanks!
The chaos
I switched the saddle to the 26.4 seatpost and it’s looking good.
Especially with the wheels
I don’t open NOS parts very often, this is pretty cool. It’s a Raleigh branded SunTour VGT. I think it’s perfect for this build since my 600 derailleur didn’t pan out.
It came with complete instructions
Looks great on the bike
The cage is set up so you don’t have to break the chain to remove the derailleur. Pretty slick.
And threw the bell on just to check it out. I think it looks fine. I’m not used to seeing a bell on my bikes though 
Pedals and shifter. It’s looking like a bike. I’ll cable it up tomorrow and hopefully get in a test ride. Time to go do Valentine’s Day stuff.
Pedals and shifter. It’s looking like a bike. I’ll cable it up tomorrow and hopefully get in a test ride. Time to go do Valentine’s Day stuff.
Last edited:
I put a squeeze horn on my kid hauling bike way back when. Worked well to halt the neighborhood dogs from charging too close. The thing was, I needed to take a hand off the handle bars to use it.And threw the bell on just to check it out. I think it looks fine. I’m not used to seeing a bell on my bikes though
Your bell, might want to consider mounting it to the handle bars. Hands then stay on the bars and ready for brakes or evasive steering.
