Tilting e-trike

[Eridez]

It's been a couple of years or so since I had a new build. I used to post with user name 'OCD' but had to change my name to get back on here. Covid lockdowns have been hard on many of us over the last 1.5 years, here's what the isolation drove me to do. (lol). While cleaning up the shop I ended up combining parts of a couple of old builds into something new. I threw in a pic of the original trike next to the revamped version. Still under construction. It is running a Nine Continent hub motor with a 45amp controller and a 52v lithium pack for about 2400 watts. Corners just like a recumbent bike but can be locked out like a regular trike.

 

[wheelbender6]

Righteous looking trike.

 

[Dominicus]

Great engineering! How do you set the tilt break? Be cool to change that as you ride. What is the plan for the stem at the very rear & does it tilt too?

 

[Eridez]

Thanks. The lock on the tilt uses a friction gear shifter from an old 80's bike, it's basically just for parking so the main trike stays upright. The trike is infinitely more fun to ride unlocked. The rear stem is just a clamp to keep the rear section pivot together (like a fork headset). I cut the stem and handle bar clamp off later. I have also started a 'trunk for my junk' to make it a bit more practical for my commute to work. I'll most likely make a lid and some fenders later, then wrap it all in epoxy/fiberglass.

 

[Eridez]

Takes up less storage space than some of my other bikes.

 

[toro1978]

So that disk brake behind the seat locks the trike in a "park" position, do I understand correctly?

 

[Eridez]

Yes, exactly. The trike was largely made from parts, materials and recycled projects that were gathering dust in my workshop I thought the disc would stop rotation totally, but you could allow a slight drag if you wanted to.

It does not feel like a trike when you ride, it corners like a recumbent bicycle using mostly lean steering rather than the under seat handlebars. It seems there's nothing in front of you when riding, it's like an amusement ride or a gaming chair. Of course you can also sit on it locked with your feet up at stop lights and see peoples reactions as you carve off

 

[Eridez]

Slight update: 84v battery pack should be arriving today. Planning to tear this thing down and gusset a few points, complete welding/painting the frame and finish the rear section, add some fenders, etc.

 

[Tallbikeman]

If you have an update would love to see it.

 

[Eridez]

Sorry, have been working on other projects (scratch built stationary bike trainer, house renos, etc) but plan to get back to this. I have begun to build up the tail box with styrofoam sm to create rear fenders and bodywork which will be covered with fiberglass/epoxy. I'll post updates when I get some progress shots. I did however switch out to an 84volt pack, makes for an even more exciting ride. lol. We're still getting crappy weather with occasional snow where I live, not fwd trike weather yet.

 

[Cmdr Ronald]

Eridez, o, Eridez, where are you Eridez? This build is fabulous & severely in need of completion. we near a year since you posted this, sir. Is you aok? Thank you.

 

[Eridez]

Sorry, the build got shelved for the past couple of years, still sitting in my workshop, still complete waiting to be finished. Turns out when I welded the rear section together the four axle bearings no longer lined up perfectly and caused the rear axle to be constantly flexed which created bearing noise. I need to rebuild the rear section before it can reliably be ridden again. I really miss riding this trike as it's so damned fun!! Have been focussing on a larger project the last couple of years.

 

[Eridez]

Back with an update on this (ongoing) side project:

Athough I really miss riding this thing, I finally got around to setting aside the time to purchase a set of 3 self-aligning HD bearings and started on the fabrication to get it operational. Although usually easier to add, fwd tends to spin and skid alot in wet or loose conditions, so I decided to add rear drive for the comeback build. I've ordered an additional adapter which will allow me to install a left side drive hub motor system to the rear axle. The rear wheel will be under driven compared to a motor being in the wheel, but will be running an 84v lithium pack, so should still have a good power/speed ratio.

 

[Jeffery A. Hunt]

Very interesting build and slick as hell, really.

 

[Eridez]

Thanks, looking forward to having it up and running again.

Unfortunately Canada Post is on strike and the parts to carry on with the build have been sitting in the depot, behind picket lines here for a month already. I don't want to weld on derailer, caliper or motor mounts until I have everything together in one place. I have lots of other projects to keep me busy in the meantime.