BO15 The Kwaka
- Thread starter HuffnPuff
- Start date
Help Support Rat Rod Bikes Bicycle Forum:
Did some measuring this arvo. Will need to extend the chain stays or dropouts as the wheel is too big. Will need around 150mm. The cranks are a bit of an afterthought on these e- scooters. The are so wide it’s not funny, could probably fit a crankset in between the bearings here. I’ll have to graft in a spare BB housing somewhere. Still need to get a good feel for where everything is going to end up.
Last edited:
Huff n' Puff in the house! Welcome back.
RaT oN~!
RaT oN~!
Wouldn't extending the chainstays make the rear suspension very soft?
It might do, moving the shock mounts further out might help. It’ll also have a fair bit less weight as the 6 lead acid batteries are out and will replace with lithium.
So far it’s all in my head as a bunch of problems to solve - which is or probably where the motivation went the first time around.
So far it’s all in my head as a bunch of problems to solve - which is or probably where the motivation went the first time around.
MattiThundrrr
Rattus All Terrainus
Bwahahaha good luck with that!
Man this is gonna be a wide body build.
Found a BB donor. Was kerbside pickup. I didn’t see how rusty it was until after it was home. Really only picked it up for the rim and BB. Put some measurements on the pic prior to cutting it up. See the gap between the chainstay and the seat tube, and the hole?
HuffNPuff build incoming!
Never seen one go that bad before and I'm in the UK, Rust is something we are good at .
Pulled the rear swing arm out. Needs about 60mm added.
Decided the front of the existing frame wouldn’t suit so got some parts
Got to chopping, need to get the hot spark gun out
New front triangle started
Decided the front of the existing frame wouldn’t suit so got some parts
Got to chopping, need to get the hot spark gun out
New front triangle started
Got to choppin. The head tube was way too long for a 26” wheel fork. The rear frame is also too wide so it will be getting sectioned.
I wanted to retain the centre stand for the motorcycle look this is also where the swingarm attaches.
Welded up the swing arm, getting better at welding I think, but it’ll still need plenty of grinding. Then mocked up some parts. The seat tube seems too far forward, but I don’t want to tilt it back too much and muck up the head angle. Will play with that some more.
Need lots more cutting and plenty of sparks added around the bottom bracket.
I wanted to retain the centre stand for the motorcycle look this is also where the swingarm attaches.
Welded up the swing arm, getting better at welding I think, but it’ll still need plenty of grinding. Then mocked up some parts. The seat tube seems too far forward, but I don’t want to tilt it back too much and muck up the head angle. Will play with that some more.
Need lots more cutting and plenty of sparks added around the bottom bracket.
Looking Cool!
How’s the rear wheel clearance once the shock is under conpression? Looks pretty close from the pic, but may just be POV.
How’s the rear wheel clearance once the shock is under conpression? Looks pretty close from the pic, but may just be POV.
It’s just sitting there for now, not connected or finalised. Yes, will probably need to change the shock mount as well as the wheel is a fair bit bigger than the original.
Spent some time with a measuring tape and an angle duplicator thingy (don’t know the real name) mocking up again and forgot to photo it. Got the seat and head angle more correct which lays it back a bit more. Combine that with lifting the rear frame and it closes the gap and helps the clearance issue from the rear wheel.
That is quite a transformation!
Small progress cutting and grinding bits to fit properly but not much to show.
I have this nice wide saddle from a chopper back up above which I plan to modify to cut the back down a bit to suit.
I have this nice wide saddle from a chopper back up above which I plan to modify to cut the back down a bit to suit.
Great looking build is coming along[emoji106]. Looks like it will be quite cool [emoji41] when it's done.
I look at that saddle and it makes me hurt a little. I hope you have better luck than I with them.
I look at that saddle and it makes me hurt a little. I hope you have better luck than I with them.
I haven’t used one before. What dramas have you had? It’s by to late for me to change direction with the saddle. I’ve got plenty of others available in the parts pile.
