Western Flyer X-53 resurrection

Rat Rod Bikes Bicycle Forum

Help Support Rat Rod Bikes Bicycle Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Joined
Sep 13, 2006
Messages
1,472
Reaction score
4,633
Location
southern PA
Rating - 100%
2   0   0
I don't know that this is a build so much as me picking away at what was once a beautiful bike in an effort to make it less tragic.

I posted this in Fresh Finds not long ago:
IMG_2011.JPG


After a couple of hours removing half of Wal-Mart's bike accessories aisle and wiping down with a dry rag, it looked a little less ridiculous:
IMG_2055.JPG


Partly because I learned that the X-53 is a sought-after collectible, but mostly because it's just so darn cool, I wanted to try to remove the horrible pool-liner-blue paint and uncover whatever was left of the original paint, which should have been black and red for 1953. But after several fruitless sessions with Goof-Off and oven cleaner, it became clear that I would need a Plan B. It was then that I stumbled upon a picture of a 1953 Western Flyer X-53 GIRLS model:
IMG_5674girls.JPG

(not mine, borrowed without permission from the CABE)

I decided that maybe the colors weren't bad after all, just the previous owner's Earl Scheib approach to painting. Maybe I could get this thing to look ok (weathered, but ok) without subjecting it to any further spray bomb paint crimes. So I set to work:
IMG_2388.JPG


I kinda like where this is going. And the horn even works!
IMG_2389.JPG


After enlisting the help of a friend who has grinding tools and chemical strippers and other implements of destruction, this is where I'm at:
IMG_2401.JPG


IMG_2396.JPG


It may be time for some of my special homebrew decal templates.
 
Last edited:
X53 is such a killer frame, it's hard to go wrong. I absolutely love the rack integrated into the frame with those additional tubes. It looks awesome already with just the cleanup, blue paint job looks a lot better with the original graphics showing on the tank
 
Daylight:
IMG_2408.JPG
IMG_2409.JPG
IMG_2410.JPG
IMG_2411.JPG
IMG_2412.JPG


Not only did the tires hold air all night, but after taking off the noisy hub shiners, this thing was dead silent on a trip around the block. (Well, except for the squeaky old seat.) And the speedometer works.

Now, I have been told that the Monark train headlight and deep fender are desirable, and maybe they look right on the correct bike, but I'm not a fan of it all on this one. If I could find a front fender that more closely matched the rear, I'd spray bomb it close-enough blue and call it a day, maybe put a rusty old headlight from my stash on it.

The guard is off the Murray-ish girls middleweight I got as part of this deal, and I think it manages to look better than that horrible chrome faux Schwinn piece. Pretty sure the correct guard, like the springer fork and headlight, are collector/restoration only items at this point. (Well, there's an original springer on eBay right now, but it's over 10 times what I paid for this bike and I don't want it that bad.)

While I don't have any hopes of finding an original springer for this, I am hoping to stumble on a newer middleweight springer like they'd have put on a Spaceliner, which I think would work great.
 
WHOA. Now that went surprisingly well...

I have been researching what parts are missing off this bike. Along with the whole front end and guard, there was this cool looking rear fender spear and reflector that are MIA:
IMG_0361.PNG


Now, I have been tinkering with some very basic 3D design software that I use with my middle school students. I managed to come up with this:
spear.png


Compared to one selling on Fleabay, it didn't look too terrible except for one small problem:
Screenshot 2024-09-14 065151.png
Screenshot 2024-09-14 064747.png


Now, I do NOT have the know-how to calculate that curve and design it in on this software, which is essentially the CAD equivalent of MS Paint. So I printed off a couple the way they were and figured that was that. Until I stumbled upon something online about using a heat gun to reshape 3D printed objects...

Out came the trusty Harbor Freight hair dryer.
IMG_2413.JPG


I attached one of the spears to an old fender with one screw in the center.
IMG_2420.JPG


A little judicious heat application, some gentle prodding, et voila. I did manage to twist the top a little, but I think it came out good for a first attempt.
IMG_2414 (1).JPG
IMG_2416.JPG
IMG_2415.JPG
IMG_2419.JPG


Before and after reshaping:
IMG_2418.JPG
 
Little stuff: Swapped out the grips for some white Western Flyer grips and cleaned the whitewalls a little.
IMG_2501.JPG
IMG_2541.JPG


Bigger news: I have acquired a working rat trap springer.
IMG_2536.JPG
IMG_2537.JPG


Head tubes measure the same (thanks for the info @rickpaulos ) so I am assuming it will be a straightforward swap.

I'm kind of stoked that the donor bike turned out to have some other parts I may be able to use, specifically the pedals and guard for starters, and maybe the chainwheel and cap. The drop center wheels would also look more correct on a 50s bike than what I have on there now, if I'm not mistaken. When did Bendix start making the model 70 coaster hub?

IMG_2539.JPG
IMG_2540.JPG


I also found this fender on the CABE. It looks to be much closer in design to the rear fender on the bike than the Monark front fender that's on it now.
colorflowfender01.jpeg
colorflowfender03.jpeg


Seller said he believes it's a ColorFlow fender, and from what I could see from researching pictures of ColorFlow bikes online, I have no reason to believe it's not. And from the ColorFlow pics I have seen, the springer rockers are very similar to the rat trap rockers, so I am hopeful that I can get this fender to work with the rat trap with some tweaking.

I do have a question for anyone who may have experience with this type of fender, since this one isn't in my hands yet: Is the lower brace attached to the back of the fender on some kind of pivot? The upper brace attaches to the rigid part of the fork, which I understand. But the lower one attaches to the end of the rocker that moves up and down with the spring/suspension travel. I assume there's some mechanism to allow it to articulate so it doesn't fatigue the metal around the attachment point on the fender, correct?
 
Last edited:
So since I picked up this bike and started tinkering with it, the garage has been deteriorating. This one came with a girls' Murray-built something-or-other middleweight that was painted the same shade of pool-liner blue and accessorized in a similarly horrific fashion. The guy wanted them both gone and I felt bad saying "well I'll help you with the one, but you're stuck with the other one."
IMG_2004.JPG


So it came home, I have been cannibalizing it for parts, and it's adding to the chaos in the garage.

Then, in my search for a rat trap springer, I discovered this girls' Spaceliner on Marketplace and added it to the mess.
IMG_2536.JPG


My wife has been giving me the side-eye about eventually getting her car back inside before it snows, so today I decided to thrash away on the bike stuff to create some kind of order. The plan was to dismantle the two girls bikes and end up with one girls bike to sell on Marketplace, one box of parts harvested for future tinkering, and one pile of scrap to give my son-in-law to practice with his new welder.

In taking the crank and pedals off the Spaceliner, I noticed this little spot on the edge of the pedal. What is this? Could it be... a reflector?
IMG_2605.JPG


Well would ya look at that. I've never seen pedals like these. You can bet these are going on the X-53.
IMG_2606.JPG


I had also hoped the Spaceliner guard would work on the X-53. The correct guard has a silver "spear" that extends from the rack support forward to a jet/rocket graphic, and I was thinking the Spaceliner guard could have a similar extension effect.
IMG_2607.JPG
IMG_2608.JPG


Alas, it doesn't seem destined to be. Though the rear mount works out fairly well, it makes the front of the guard too short. Also, the rear of the guard is lower than the chain, which will only get worse when I swap out the 18t rear cog for a 20t, which I ordered from Amazon a couple days ago.
IMG_2609.JPG


Now, I am planning to change out the 46t sprocket for a 44t, so the guard won't have to be quite as far forward, but I don't think that'll make up the length I'd need. I haven't given up yet, but I'm thinking I'll probably end up using the blue Murray "tailfin" guard that was on there earlier.

So with both girls bikes blown apart, I pieced one back together on the Spaceliner frame. I added a set of bars and a Schwinn crank/sprocket from the basement stash, and the pedals and guard that were on the X-53 when I got it, et voila. We have a complete working girls bike. It even looks kinda cool.
IMG_2615.JPG


While I was out there, I compared the cheap spray bomb I bought at Ollie's yesterday with the rear fender. I know the cap isn't going to be a perfect representation of the color, but hey, if it's even in this ballpark, it's good enough for me. The cap is a dead match. (I just KNEW that the cheapest Dark Blue paint I could find at a discount store was going to be the color the previous owner used.) The ColorFlow fender which will be getting this paint is on its way to me, according to UPS.
IMG_2604.JPG


Finally, here are pics of that springer on the X-53 in daylight:
IMG_2601.JPG
IMG_2602.JPG


I am hoping that the ColorFlow fender will somehow fit in there without major surgery. I rode it up and down the block and it seems to work well, though it bottoms out pretty easily. Considering this bike was designed for kids who were maybe 125-150 lbs and I'm over 200, this should not be a surprise to me. :21: Still looks cool and I like the novelty.
 
Got my Amazon package yesterday with a 20t rear sprocket for this thing, so I spent an hour juggling cranksets, sprockets, and bottom bracket pieces. This is what I ended up with.
IMG_2639.JPG
IMG_2643.JPG
IMG_2640.JPG


I got it with a 46 tooth sprocket and 18 tooth rear cog, which was geared higher than I like. I stripped this 44t off the bonus girls middleweight that came with this bike, so on it went to complement the new 20t rear cog. Pretty sure this chainwheel is originally off a Rollfast (anyone confirm that?) and it looks kinda like the Murray one that should be on there, so I'm calling that a win. A quick test cruise up and down the block has this geared right where I like it now. Love these pedals too.

Really hoping I can get a fender to fit in here. UPS says the one I bought on the CABE is due here Thursday.
IMG_2642.JPG
 
Last edited:
UPS got the fender here a day early. After adding a couple of dimples, it fits up in the Spaceliner fork perfectly, and it clears the tire with the suspension bottomed out. Now I just have to shorten the front support struts. Then we'll see how well that spray bomb really matches the rear fender.
IMG_2672.JPG


However, this is likely gonna sit for at least a few days, because my daughter is getting married Saturday and starting tomorrow it's all hands on deck.
 
ok so... didja ever do a test shot of something that came out SO GOOD that you just knew you'd never be able to replicate it for the real thing? well, that's kinda what happened here, except not really.

I have been thinking I'd use my diecut stencil technique to fake together some graphics for this thing. I don't have the correct Western Flyer font, but I found something that's definitely the same idea.
Screenshot 2024-10-28 221832.png


It's not going to fool anyone who knows these bikes, but that's not the goal anyway. I just wanted something that looked right for this era and style. I'm even faking some ideas for stuff to use on the guard, even though the original X-53 didn't have anything on the guard but a jet fighter looking graphic (which I think was actually stamped into the metal of the guard).
Preview - Colors.png


Anyway, I wanted to put the Western Flyer script on the tank where the original would have been, like this (pic robbed from The CABE):
tank graphics.jpeg


I had an idea that if I painted the script once in red, then overlapped it just a little in white, it'd be a reasonably similar effect to the original. So I tried it on a junker girls' tank:
IMG_3003.JPG
IMG_3002.JPG


DANG. That looked pretty good, I think. Just have to get it to look that good AGAIN on the halves of the tank. Twice.
IMG_3004.JPG
IMG_3005.JPG


Well, I actually got it lined up correctly and the paint came out great, except for one thing: the junk paint on the tank pulled up with the stencil when I was done. Which I should have figured for, seeing as how it was already flaking off in spots. I ended up using a wad of duct tape to try to randomize the paint loss elsewhere on the tank so it wouldn't look like it was just a square around the script.
IMG_3006.JPG


Well, it looks old and weathered, anyway. It wouldn't even bother me if the whole tank was evenly chipped, but you can tell that there's a rectangle around each script where the tape pulled paint off.

I guess it's not really any more terrible than it was before. :21:
IMG_3008.JPG
IMG_3009.JPG
IMG_3011.JPG
IMG_3012.JPG


Oh and as a side note, I got the front fender attached in what looks like a somewhat correct manner. Does this look ok? I swapped out the upper fender strut for one off a junker 24" fender.
IMG_2988.JPG
IMG_2990.JPG
IMG_2993.JPG
IMG_2994.JPG
IMG_2995.JPG
IMG_2996.JPG
 
The logo you did came out great, patina matched and all. I don't think anyone will notice that it's not original unless you point it out. The forks and fender are looking great too. Nice work!
 
This rear fender brace has been bugging me since I started tinkering with this thing.
IMG_3090a.JPG


Based on pictures I've seen of originals, that light blue painted strap across the fender is supposed to go INSIDE the fender. But I had no idea if this was the original part or something the previous owner cobbled up, and if that was the case, if the holes would line up after swapping inside for outside since the radius would change somewhat. Well, today I moved it to inside the fender and it bolted up just fine.
IMG_3142.JPG
IMG_3143.JPG


I like that it pushes the fender out a little further from the tire. I think it just looked a little off before.
IMG_3139.JPG



And since I was playing with the fender and brace, I took out my 3D printing test shots to see how close I came with them:
IMG_3153.JPG
IMG_3151.JPG
IMG_3154.JPG


Not too bad, I don't think. Gotta make a little adjustment to the reflector housing so the mounting points come closer to the rack supports, but I think I'm almost there.

The spear is painted with the same hammered metal effect paint as the lower front fender support. Once I get the reflector housing right, it'll get the same paint.

edit: ehhhhh I dunno
x53-3dp-spear and taillight.jpg
 
Last edited:

Latest posts

Back
Top