TRADITIONAL Hops and Gnarly

Rat Rod Bikes Bicycle Forum

Help Support Rat Rod Bikes Bicycle Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
After two months I have yet to have the whole bike together until this morning.

So with less than 48 hours on the clock, here is the completed Hops and Gnarly!

IMG_7880.JPG
 
That’s one hot bike, I love it!
I still don't have a durable solution for chrome patina, but this quick application looks good. A light rust was all that I wanted.

View attachment 275499

This was fresh new chrome when I started.

View attachment 275502

I sprayed a light coat of rattle can clear and after it dried I went over it with wood stain. The big drawback is that it will easily scrape off exposing the chrome. I think a durable finish like this is possible by sanding first, but I haven't cleared that with the owner. This can easily be removed with a rag and acetone.
I like the way this turned out. It looks good and leaves the option of going back to the nice chrome at some point if desired. Really nice build. Kudos!
 
Wow! Dad gum! Excellent work sensi!

Those 'special Hoppy edition' thickBricks are great on there too!

Thanks! The tires and wheels were my surprise that I've been holding back!

This was not a complete bike when I got it to restore, so I put a few of my own parts with it to make it as 'custom' as I could get by with. After the build-off it will come back apart and will eventually be put together as stock.

When I was looking for a wheelset for it, I thought how cool would it be to put that 50mm black Felt wheelset and ThickBricks on it. I was thrilled when I tried them a few weeks ago and confirmed that they would fit without any clearance issues!

I did however have one major hurdle. The modern axle on the front hub was far too big to fit through the hole on the front fork. Because it has a hole and not a slot, filing flats like I would normally do for a slotted fork was not an option. And of course, drilling out the fork bushings was an absolute no!

IMG_7734.JPG


So I found an axle that was the correct size for the fork that had a similar cone for the loose ball bearings and swapped it out. It's not an exact match, but it works.

IMG_7733.JPG


It was a complete pain in the bum to assemble inside the fork! There was not enough room for a proper jam nut, so I had to adjust it after it was all assembled, and then the outer nut tightened against the bushing which locked everything in place. It was a tricky process!

IMG_7735.JPG
 
Excellent Build!!!! Love the patina match and all the cool details! BRAVO!!!!
That wheel axle had to have been a major pain for sure. Glad you had the patience for it. Can't go wrong with a pair of Thick Bricks!
Has Cousin Charlie seen it yet????
 
Excellent Build!!!! Love the patina match and all the cool details! BRAVO!!!!
That wheel axle had to have been a major pain for sure. Glad you had the patience for it. Can't go wrong with a pair of Thick Bricks!
Has Cousin Charlie seen it yet????
Thanks!
Charlie has not seen it yet. I did text him a picture of his membership certification in the Troopers Club though. He responded with "cool". :cool:

IMG_7888.JPG

IMG_7889.JPG
 
Fantastic build! Another one!😎
Thank you!

You should consider including this one in your finished thread. Too cool. :cool2:
Thanks, I'll do that!

I always figured if they were good enough for Bonham, they're good enough for me.
I have a similar sized jazz kit, but '62 WFLs in black diamond pearl. I've had good luck with them in recording situations.
Rock on!
My whole kit would fit inside Bohnam's kick! :21:
The '62 WFL sounds like a nice one. I've never used my Jazz kit for recording but I have used that Supraphonic snare in the studio before. :)
 

Latest posts

Back
Top