Bonefish: The Beginnings

Rat Rod Bikes Bicycle Forum

Help Support Rat Rod Bikes Bicycle Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I know I'm not going to win. I might not even finish. But Matti ain't quitting. Got a couple of hours' work done on the fish
IMG_20220211_124214392.jpg

Switching over to the 40 tooth is going to cost me some top end for sure, I lost more teeth than Bobby Clark!
IMG_20220211_124205636.jpg

But the look speaks for itself. Some old beat down alloy pedals went on too.
IMG_20220211_125632632.jpg
 
For grease, I'm trying a new tool. Suggested by a user who is currently slipping my mind. Sorry. Made an injector by cutting off the tip of the needle on a meat flavor injector.
IMG_20220211_131636969.jpg

Pack the grease in, and apply with precision!
IMG_20220211_131825321.jpg
IMG_20220211_132000398.jpg
IMG_20220211_132148788.jpg

Don't worry, I still made a bit of a mess
IMG_20220211_132221703.jpg

Don't forget to save the cap to prevent spillage or contamination
IMG_20220211_133213428.jpg
 
Last edited:
Best way to grease bearings is to hold the bearing in the palm of your hand, put a dab about a quarter size of grease in the middle and then work it into the frame of the bearing with your index finger, making sure all of the balls are surrounded by grease and the frame is filled. That's old school and it will last. I do like your injector, could be handy on a quick axle lube...

C.
 
Reality check day. The back wheel just isn't going to cut it. It is far too wobbly and warped for this build. I have work to do.
IMG_20220219_155211210.jpg

The original steel wheels from Fishbone are in perfect condition, they're just nothing special. Basic Chinese stuff from over a quarter century ago, Pheasant hub or something.
Just the back mag is a mess, the front is still usable. The pegs are gone, no room on the axle bolt. We're going to have to see if I can stand the mismatch
IMG_20220219_163908706.jpg

I will be surprised if I make it to the deadline with a working bike, it definitely won't be the finished product
 
Last edited:
Reality check day. The back wheel just isn't going to cut it. It is far too wobbly and warped for this build. I have work to do.View attachment 186203
The original steel wheels from Fishbone are in perfect condition, they're just nothing special. Basic Chinese stuff from over a quarter century ago, Pheasant hub or something.
Just the back mag is a mess, the front is still usable. The pegs are gone, no room on the axle bolt. We're going to have to see if I can stand the mismatchView attachment 186202
I will be surprised if I make it to the deadline with a working bike, it definitely won't be the finished product
I hope you make it to the “finish”. But are they ever finished? I am doing my best to get my build to a “finished” state, but I also plan to tear it down again, repaint and add some touches. Maybe for a future build off. I already have some things I don’t currently like about my build but just going with it for now. All the luck!
 
Cleaned and installed the old grips provided by @ingola thanks again, man, the cockpit is all set!
IMG_20220221_112229340.jpg
IMG_20220221_112139176.jpg
IMG_20220221_112310492.jpg

It is tough to get a good picture in the basement. I love these grips, bring me back every time I grab them. My homie Dorf from back in the day had one of those dirtbike bicycles with these things, and we would bomb the hills at his farm, or out at the Moose Creek quarry.
image57e7588b13_blowup.jpg

Probably not the one Dorffy had
 
the cockpit is all set!
Or is it? Humor the ramblings of a madman. Sometimes I yearn for an actual complete bike. Remember those 30" wide moto bars I took the brace from?
IMG_20220221_112639490.jpg

They are wiiiiiiiiide! :rockout:
IMG_20220221_112542409.jpg
IMG_20220221_112512715.jpg

This, however awesome, paints me into a corner. No longer running "muscle" bars, but they certainly are crazy. I think I'd have to put on a bigger tire up front, and then I just have a banana seat, 1 of 3. I don't think this is the place for this bar.
IMG_20220221_112605319.jpg

Opinions? Also, here's the spoked wheel mounted on the front for comparison purposes:
IMG_20220221_113843028.jpg
 
Dug into the treasure chest and found some old stuff for that bag...
IMG_20220221_115424102~2.jpg

Can't be too many Stalemate patches left out there in the wild. Most of my old punk patches have gone missing over the years. I used to have a stack. Working up the nerve to sew these things together. I expect blood.
 
Dug into the treasure chest and found some old stuff for that bag...
View attachment 186349
Can't be too many Stalemate patches left out there in the wild. Most of my old punk patches have gone missing over the years. I used to have a stack. Working up the nerve to sew these things together. I expect blood.
I have one of those two quite a few more to even all the old posters
 
Or is it? Humor the ramblings of a madman. Sometimes I yearn for an actual complete bike. Remember those 30" wide moto bars I took the brace from?View attachment 186344
They are wiiiiiiiiide! :rockout:
View attachment 186343View attachment 186342
This, however awesome, paints me into a corner. No longer running "muscle" bars, but they certainly are crazy. I think I'd have to put on a bigger tire up front, and then I just have a banana seat, 1 of 3. I don't think this is the place for this bar.View attachment 186345
Opinions? Also, here's the spoked wheel mounted on the front for comparison purposes:View attachment 186346
Looks great with the bars and the spokes! Maybe a slight seat drop and stem raise would help the proportions in my opinion. I dig it!
 
I like the crossbar apes better. Keep the mag front too.
 
It's settled: the mag is back on. Shortened the axle bolt 1/2" on each side with the dremel. Probably could have removed 3/4". Also cut the rear section of the outer brake cable that attaches to the noodle. Probably could have left 1/2" more on there :rolleyes: .
So close i can almost taste it, and yet still so far.
 
Back
Top