Nice Flathead motor for the bee.
Smart thinkin!
Smart thinkin!
TRADITIONAL SHAOLIN SPITFIRE (Wu Tang Forever)
- Thread starter BobbyStillz
- Start date
Help Support Rat Rod Bikes Bicycle Forum:
A little progression video, for fun.
The 'W'
Was planning on using earth magnets to attach the 'W' to the top plate...but the stainless steel isn't magnetic 
I considered mounting these shelf clips to hold it, but the positioning would be off.
Experimented with a suction cup, but not sure how long it would hold on a ride.
So I put rubber washers top and bottom and ran the bolt through. Leaving this as inspiration, for now, but will fabricate a low profile hanger, in similar fashion to a plate hanger without springs.
It can be used as a bottle opener, so I want to be able to detach and re-attach it with some ease.
I considered mounting these shelf clips to hold it, but the positioning would be off.
Experimented with a suction cup, but not sure how long it would hold on a ride.
So I put rubber washers top and bottom and ran the bolt through. Leaving this as inspiration, for now, but will fabricate a low profile hanger, in similar fashion to a plate hanger without springs.
It can be used as a bottle opener, so I want to be able to detach and re-attach it with some ease.
Sticking with the diamond grips. The color and pattern are too perfect.
@MattiThundrrr Here's your duel
Going to tighten the screens all the way down. The thread pitch is way different, though the diameter matches, so I'll have to crank 'em down.
@MattiThundrrr Here's your duel
Going to tighten the screens all the way down. The thread pitch is way different, though the diameter matches, so I'll have to crank 'em down.
Sticking with the diamond grips. The color and pattern are too perfect.
View attachment 273537
@MattiThundrrr Here's your duel
View attachment 273538
Going to tighten the screens all the way down. The thread pitch is way different, though the diameter matches, so I'll have to crank 'em down.
View attachment 273539
The audio guy inside of me laughs at this because (if these were functional), there would be so much feedback
MattiThundrrr
Rattus All Terrainus
Wu Tang badge ain't nothing to mess with!
Was planning on using earth magnets to attach the 'W' to the top plate...but the stainless steel isn't magnetic
View attachment 273532
I considered mounting these shelf clips to hold it, but the positioning would be off.
View attachment 273533
View attachment 273536
Experimented with a suction cup, but not sure how long it would hold on a ride.
View attachment 273534
So I put rubber washers top and bottom and ran the bolt through. Leaving this as inspiration, for now, but will fabricate a low profile hanger, in similar fashion to a plate hanger without springs.
View attachment 273535
It can be used as a bottle opener, so I want to be able to detach and re-attach it with some ease.
Get some peel and stick magnetic tape. Or some velcro.
Now that I see both mic'ed up steering arms together, I like this configuration better. Love the grips too.
They look like Battle Mic-Maces! Mace-Mics? Either way. Perfect.
Bang a gong and let the battle begin!
They look like Battle Mic-Maces! Mace-Mics? Either way. Perfect.
Bang a gong and let the battle begin!
View attachment 273655
"And if you want beef, then bring the ruckus. Wu Tang Clan ain't nothin' to ____ with!"
As previously mentioned, the thread pitch on the mic screens are different than the pipe reducers. I tried forcing it through, and I got about 2 threads down on one side, but can barely get a single to catch on the other side. May need to file down a bit or try and cut a new channel with a dremel, as I don't have a tap that size/tpi.
The Renaissance Man
__CERTIFIED DIVER__ (Open Water & Open Dumpster)
Staff member
Moderator
Pro Member
Foam double stick tape.Was planning on using earth magnets to attach the 'W' to the top plate...but the stainless steel isn't magnetic
View attachment 273532
I considered mounting these shelf clips to hold it, but the positioning would be off.
View attachment 273533
View attachment 273536
Experimented with a suction cup, but not sure how long it would hold on a ride.
View attachment 273534
So I put rubber washers top and bottom and ran the bolt through. Leaving this as inspiration, for now, but will fabricate a low profile hanger, in similar fashion to a plate hanger without springs.
View attachment 273535
It can be used as a bottle opener, so I want to be able to detach and re-attach it with some ease.
I wonder if you could grind one side of your bolt a bit to create a makeshift tap?
How so? Having a hard time picturing what you mean. Thanks
