TRADITIONAL SHAOLIN SPITFIRE (Wu Tang Forever)

[Captain Awesome]

Was planning on using earth magnets to attach the 'W' to the top plate...but the stainless steel isn't magnetic

View attachment 273532

I considered mounting these shelf clips to hold it, but the positioning would be off.

View attachment 273533

View attachment 273536

Experimented with a suction cup, but not sure how long it would hold on a ride.

View attachment 273534

So I put rubber washers top and bottom and ran the bolt through. Leaving this as inspiration, for now, but will fabricate a low profile hanger, in similar fashion to a plate hanger without springs.

View attachment 273535

It can be used as a bottle opener, so I want to be able to detach and re-attach it with some ease.

You just need stronger rare earth magnets. Put one on the Wu and another underneath that stamped top plate.

Strong enough that the two are virtually inseparable by themselves but the top tree can be a buffer to temper the magnetism


We use a hidden attachment similar to that in one of our customers parts. The hidden magnet is just held in place with CA glue

 

[BobbyStillz]

You just need stronger rare earth magnets. Put one on the Wu and another underneath that stamped top plate.

Strong enough that the two are virtually inseparable by themselves but the top tree can be a buffer to temper the magnetism


We use a hidden attachment similar to that in one of our customers parts. The hidden magnet is just held in place with CA glue

The plate is magnetic, the 'W' is not.

 

[Captain Awesome]

The plate is magnetic, the 'W' is not.

Ah yes. Sorry, my brain wasn’t braining

 

[BobbyStillz]

New music video!

 

[Pondo]

I was thinking of something like this


I don’t know if the bolt needs to be hardened but it would help.

 

[Da Gas Man]

Maybe if you were able to cut the Coupling down a bit to about
four threads. This would tighten up the space a bit. Also keep up
with the attempts to re-thread of the mic heads. Almost there.

 

[Da Gas Man]

Maybe if you were able to cut the Coupling down a bit to about
four threads. This would tighten up the space a bit. Also keep up
with the attempts to re-thread of the mic heads. Almost there.

And if you're unsure about the work and fitment, consider the low strength thread lock.
Help keep them from accidentally twisting off from vibration.

 

[BobbyStillz]

Still working on logistics, so I'm sorry for the fiiler, but here's another highlight reel.

 

[BobbyStillz]

Hmmmm...

 

[BobbyStillz]

Remember kids... If you don't put your name on your homework, no one will know it's yours.

 

[Wayne]

Hmmmm...

View attachment 273895

Are they thick enough, turn them into tire valve caps?

 

[BobbyStillz]

Are they thick enough, turn them into tire valve caps?

Not quite. However, I do have some valve caps already planned. These charms are metal, and I have a couple ideas rattling around. Sometimes, you don't know what 'jewlery' to wear until the 'outfit' is complete. We shall see...

 

[BobbyStillz]

Worked on a spring clip mounting for the 'W' today.

And then... righty-tighty became righty-loosey.

 

[BobbyStillz]

Let's try this again...

 

[kingfish254]

 

[BobbyStillz]

I had planned on using these as valve caps on a previous build. However,I went a different direction on that build, so I will try these again for my current build.

 

[BobbyStillz]

Ok, 'W' is in place!

I hit the exposed clip areas with a red sharpie which matches the metallic red and anodized red of the fork assembly.

 

[BobbyStillz]

Finished the other grill/headers.

I will go back and rub off the markings later on, but wanted to try fitment before work.

 

[BobbyStillz]

Tried flaring upward to start. I like it, but don't love it.

So I pulled the angle down a bit. This is good. I think I'll call that done (fitment-wise).

 

[kingfish254]

Looking Super Bee sharp brother!!!